Industries > Oil- and Abrasion-Resistant TIJ Traceability Code Printing on Automotive Metal Parts

Share this article to your friends
  • UNIPLUS
  • UNIPLUS
  • UNIPLUS
  • UNIPLUS

TIJ Printing for Oil-Resistant Traceability Codes on Automotive Metal Parts-Uniplus


Oil- and Abrasion-Resistant TIJ Traceability Code Printing on Automotive Metal Parts

Automotive parts that need long-term traceability are often marked directly on the metal surface, not only on the outer packaging. Cartons are removed on the assembly line, while the part itself stays in the vehicle for years. When a quality issue arises, the automaker relies on the lot or serial number on the part to trace back the production date, line and raw-material batch. Among TIJ printing applications in manufacturing, automotive parts set some of the stricter durability requirements.

Printing oil- and abrasion-resistant traceability codes on metal with TIJ (thermal inkjet) comes down to three questions: whether the ink adheres to the metal, where the print station sits in the process, and whether code quality can be proven with data.

Automotive Traceability Codes Are Marked on the Part Itself

Direct Part Marking (DPM) means applying an identification code directly to the part surface rather than to a label or the packaging. The Automotive Industry Action Group (AIAG) publishes B-17, a guideline for 2D codes marked directly on parts. It covers Data Matrix and QR Code symbols applied by laser, dot peen and inkjet.

Inkjet is therefore one DPM option for automotive applications. This does not mean every automaker or part category accepts ink marking. Whether you can use it depends on each automaker's specifications.

The required level of traceability depends largely on the automaker's specifications. IATF 16949 clause 8.5.2.1 requires organizations to analyze internal, customer and regulatory traceability requirements. Where the customer or regulations require it, each individual product must also carry serialized identification. Automakers also issue their own customer-specific requirements (CSRs). Some OEMs publish theirs on the IATF customer-specific requirements page. Detailed marking specifications, however, are usually found in part drawings and customer engineering standards.

A supplier serving several automakers may therefore face a different symbology (the barcode type, such as Code 128 or Data Matrix), data content, character height and minimum grade for each.


Common Data Content in Traceability Codes

Actual fields and formats follow the automaker's specification. Common content includes:

  • Part number: matching the drawing and approval documents.
  • Lot or serial number: lot numbers for batch traceability; safety or functional parts may require a serial number per piece.
  • Production date and shift: narrowing the time window of an issue.
  • Line, equipment or mold number: locating the source of an issue.
  • Supplier code: identifying the source plant in a multi-tier supply chain.


Where TIJ Printing Fits

TIJ printing leaves ink on the part surface, whereas laser and dot peen leave a mark in the material itself. If a part will go through heat treatment, shot blasting, painting or other processes that remove or cover the surface after marking, laser or dot peen is usually the more suitable choice.

Two situations suit TIJ evaluation:

  • The main surface processing is complete and later processes will not significantly damage the ink layer.
  • The OEM or Tier 1 customer's engineering specification permits ink marking of lot numbers, serial numbers or barcodes, with acceptance criteria for code quality, adhesion and durability.

Passing a code quality verification does not mean oil resistance, abrasion resistance or long-term traceability requirements have been met; each must be confirmed separately.

Which TIJ Ink Should You Use on Metal Parts?

For bare steel, aluminum alloys and some metal coatings, solvent-based TIJ ink is usually the first option to evaluate.

Dense metal surfaces do not absorb ink the way paper does. The ink has to form an adherent film on the surface. Solvent evaporation helps the ink layer dry quickly. Actual adhesion, however, depends on how well the resin in the ink formulation bonds with the substrate surface. Rough or porous coatings need to be evaluated individually.

Water-based dye and pigment inks are designed mainly for porous or semi-porous materials such as cartons, paper and wood. On metal, they need separate testing.

Solvent-based ink is a starting point, not a conclusion. Three conditions change the result:

  • Surface energy: whether the ink can spread on the metal surface.
  • Coating or pretreatment: plating, conversion coatings (thin chemical layers such as phosphate or chromate treatments) and paint all change surface properties.
  • Actual oil and abrasion requirements: which fluids the part contacts, where friction comes from, and how long the code must last.

TIJ Printing on Metal Parts-Uniplus


Surface Energy and Coatings Set the Starting Point for Adhesion

Three terms describe how ink behaves on a surface:

  • Surface energy: how strongly a solid surface attracts a liquid.
  • Surface tension: how strongly a liquid holds itself together.
  • Wettability: how easily a liquid spreads across a surface.

Roughness and contamination also play a part. When the surface energy is significantly lower than the ink's surface tension, the ink may not spread evenly and can form droplets, leaving ragged edges after drying. This is a general indication of poor wetting, not a direct measure of adhesion.

Production lines often check wettability after cleaning with dyne pens (test pens that show whether a surface wets easily) or contact-angle measurement. These checks only indicate wettability. They cannot replace adhesion and durability testing.

Surface ConditionPrinting Evaluation Focus
Degreased bare steel, cast ironConsistency of cleanliness; parts left too long after cleaning may re-oxidize or pick up oil mist
Aluminum alloys (including die castings)Release agent residue; sealing condition of anodized parts affects adhesion
Plating, zinc plating, conversion coatingsAdhesion varies widely by coating type; test using actual parts
E-coat (electrodeposited paint), powder coatingCoating formulation determines surface energy; wax- or fluorine-containing coatings usually show weaker adhesion
Residual rust-preventive oil or cutting fluidPrinting directly is not recommended; add a cleaning step first


Quantify Oil and Abrasion Requirements First

For oil resistance, clarify which oil, how it contacts the part (drips, immersion or wiping), and at what time and temperature. For abrasion resistance, identify the source of friction: parts rubbing against each other in handling, operators picking them up with gloves, or contact with assembly fixtures. Once these conditions are written into the sampling plan, different inks can be compared on a common basis.

When Uniplus supports customer sampling, customers sometimes have not yet confirmed the test oil and acceptance method specified by the automaker. Clarifying the specification first can shorten the evaluation process more than comparing additional inks. For solvent-based cartridge specifications and compatible models, see the Uniplus industrial ink cartridge page.

Place the Print Station After Degreasing and Cleaning

After machining, metal parts may carry residual cutting fluid, machining oil, rust-preventive oil or cleaning agents. These residues may alter surface wettability and interfere with contact between the ink layer and the substrate, increasing the risk of uneven printing or poor adhesion.

The print station is generally best placed after suitable degreasing and cleaning, once the surface is fully dry and free of incompatible residues that affect adhesion. The exact position still depends on the part's surface treatment, downstream processes and sampling results.


Drying and Part Temperature After Cleaning

Residual moisture after cleaning also affects adhesion. Warm parts accelerate solvent evaporation, which can change dot size and drying speed; cool parts in a humid environment may develop condensation. During trial runs, record the distance between the cleaner exit and the print station, and the part temperature on arrival at the print station.


Include Post-Printing Processes in the Evaluation

If parts receive rust-preventive oil, assembly grease or another wash after printing, these exposures fall within the scope of durability testing. Two practices:

  • Use the fluids the part will contact after printing as your oil-resistance test fluids. Handle them according to each chemical's Safety Data Sheet (SDS), customer specifications and laboratory safety procedures, and do not mix them.
  • The ink needs sufficient drying time. Confirm the interval between printing and the next contact process during sampling.

If ink adhesion is inconsistent, first check cleaning, drying conditions and part temperature before the print station, and only then consider a different ink. When pretreatment conditions are unstable, changing the ink rarely solves the problem.

Symbology and Size Planning for TIJ Traceability Codes

The AIAG B-4 part identification standard recommends Code 39, Code 128, Data Matrix and QR Code; which one to use still follows the automaker's specification. 2D codes usually hold more data in the same area than linear barcodes.

Their built-in error correction also tolerates some localized damage, which adds reading margin for parts exposed to oil or friction. Error correction has limits, however, and cannot replace the durability of the ink layer itself.

Actual capacity depends on the data format, the module size (the size of each individual cell in the code) and the quiet zone (the blank margin required around the code).


Code Height and Marking Area

Uniplus half-inch cartridges have a maximum print height of 12.7 mm, and one-inch cartridges 25.4 mm. Print height is only a size limit. Whether a code reads reliably also depends on data volume, number of modules, module size, quiet zone and reading distance. Plan these together with the automaker's specification and your reading equipment. For planning small 2D codes, see high-resolution TIJ ID code printing for PCB and electronics manufacturing.


Curved Surfaces, Recesses and Marking Position

TIJ requires a short printhead-to-substrate distance, so curved surfaces, steps or recesses shift drop placement and distort the code. Choose a flat area for marking and hold the part in a fixture so that the print distance is consistent for every piece. For experience with curved substrates such as metal tubes, see TIJ printing on glass bottles, acrylic and metal tube packaging.

Verifying TIJ Traceability Codes With ISO/IEC Grades at End of Line

A code that reads on the line's scanner will not necessarily read at downstream stations, on different reading equipment, or years later. Barcode verifiers measure parameters such as symbol contrast (the difference between dark and light areas), modulation (how consistent that contrast is across the code) and geometric quality (whether the code's shape and spacing are accurate). They then assign a quality grade under specified conditions.

Three ISO/IEC standards each have their own role:

Code TypeStandardScope
Linear barcodes (Code 128, Code 39, etc.)ISO/IEC 15416:2025Measures parameters by linear scanning and assigns an overall grade
2D codes (Data Matrix, QR Code, etc.)ISO/IEC 15415:2024Measurement and grading methods for multi-row and matrix 2D symbols
2D codes marked directly on the part surfaceISO/IEC 29158:2025Builds on ISO/IEC 15415, modifying illumination conditions and the measurement and grading of certain parameters

ISO/IEC 15415:2024 can be applied to direct part marks. The standard itself notes, however, that combining it with ISO/IEC 29158 gives results that better match real scanning performance. This is because direct marks on metal often need different lighting conditions to measure accurately.

2D codes printed on metal parts may therefore be verified with the ISO/IEC 29158 method where the customer specifies it. The standard used, the measurement conditions and the minimum passing grade all follow the automaker's specification.

A code quality grade reflects symbol quality under specified measurement conditions. It cannot, on its own, prove the ink's resistance to oil, abrasion or long-term weathering. Parts with durability requirements need separate ink adhesion and durability testing.


Two Points for Verification

Barcode quality verification serves different purposes during initial validation and routine production:

  • Sampling stage: measure before and after oil and abrasion testing, compare grade changes, and record the ink layer's adhesion at the same time. The two results are related, but neither replaces the other.
  • Mass production: sample at end of line at the frequency the customer requires, and keep verification records.

Uniplus recommends keeping verification records from the sampling stage onward. During customer audits, documented barcode verification results provide stronger evidence than visual inspection alone. A declining quality grade may also indicate changes in printhead condition or surface preparation.

Sampling and Durability Testing Before Adopting Solvent-Based TIJ

Adoption can follow these six steps:

  1. Obtain actual parts: use cleaned parts with the same surface condition as mass production, not sample plates or test coupons.
  2. Confirm the automaker's specification: symbology, data content, code size, minimum grade, and the durability test method and acceptance criteria.
  3. Print and record conditions: part temperature, ambient temperature and humidity, print distance, and time from printing to the next process.
  4. Durability testing: use the oils specified or actually encountered on the line, define contact temperature and time, friction material, force, number of cycles and acceptance criteria, and pair with ink adhesion testing.
  5. Grade verification: measure before and after testing according to the applicable ISO/IEC standard and compare.
  6. Small-batch trial: confirm continuous printing stability at actual line speed and cycle time, covering restarts after stoppages, long runs and different part batches.


Checks for Equipment Makers

For TIJ equipment makers and system integrators, ink adhesion on metal is only one adoption condition. Equipment makers should also check cartridge compatibility with the controller, print height, printhead mounting and fixtures, line speed, and restart stability after a stoppage. Half-inch and one-inch cartridges differ in printhead mounting and controller settings, so they cannot be swapped directly. Equipment makers should check the mounting and controller configuration of their own systems before choosing a cartridge size.

Uniplus offers solvent-based industrial ink cartridges in both its half-inch and one-inch product lines, and provides a compatibility verification service: share your machine model during discussions and we will help evaluate feasible solutions. Actual compatibility and print performance depend on equipment configuration and sampling results on actual metal parts.

Extending Durability Evaluation to Water, Weather and Chemical Exposure

The method for evaluating oil and abrasion resistance (quantify the environment first, sample on real items, then verify with data) applies equally to other harsh environments. Agricultural packaging offers two common extensions:

  • Seed and pesticide bags: when used outdoors or stored in humid warehouses, the focus is how sunlight, rain and humidity affect the printed code.
  • Pesticide and fertilizer packaging: some contents are corrosive; the focus is whether the printed code will contact these chemicals and the ink's chemical resistance, confirmed against the actual formulation and exposure conditions.

The substrate changes from metal to woven plastic bags or laminated film, but the process of defining the environment first and then verifying by sampling stays the same. Applications in other manufacturing, logistics and specialty industries are covered in Complete TIJ Printing Applications for Manufacturing, Logistics, E-Commerce and Specialty Industries.

Discuss Your Metal Part Coding Requirements With Uniplus

Preparing the following information before contacting us helps the sampling evaluation get to the point faster:

  • Part material and surface treatment
  • Print position, available area and part shape
  • Symbology, data content and the automaker's minimum grade
  • Oils the part will contact after printing and the durability test method
  • Current coding equipment model

Contact Uniplus to discuss your metal part coding requirements. Our team can help assess suitable solvent-based inks and sampling conditions based on part material, equipment model and automaker specifications.

The above brand names are trademarks of their respective owners.

All brand names displayed on this page are used only to show the compatibility of the respective products.

We use cookies to personalize content and ads, provide social media features, and analyze our traffic. By clicking Privacy Policy.

Please contact us for more information